The often use tool to map vmdk to Linux disk is lsscsi.But if in meantime you changed the scsi controler type the order of scsi device in Linux changed too and you can't rely on lsscsi output any more.
The most reliable way to find the ESXi mapping to scsi devices in Linux is using pciSlotNumber (ESXi) and Physical Slot (Linux).
I am a RPM based Linux user (Centos, RHEL, Fedora etc.)
Install packages:
# yum -y install pciutils lshw
Check businfo on Linux:
# lshw -businfo | grep scsi
pci@0000:00:10.0 scsi0 storage 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI
scsi@0:0.0.0 /dev/sda disk 42GB SCSI Disk
scsi@0:0.0.0,1 volume 500MiB Linux filesystem partition
scsi@0:0.0.0,2 /dev/sda2 volume 39GiB Linux LVM Physical Volume partition
scsi@0:0.1.0 /dev/sdb disk 1073MB SCSI Disk
pci@0000:02:01.0 scsi3 storage 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI
scsi@3:0.0.0 /dev/sdc disk 1073MB SCSI Disk
pci@0000:0b:00.0 scsi4 storage PVSCSI SCSI Controller
scsi@4:0.0.0 /dev/sdd disk 1073MB SCSI Disk
scsi@4:0.1.0 /dev/sdg disk 1073MB SCSI Disk
pci@0000:13:00.0 scsi5 storage PVSCSI SCSI Controller
scsi@5:0.0.0 /dev/sde disk 1073MB SCSI Disk
scsi@5:0.1.0 /dev/sdf disk 1073MB SCSI Disk
scsi2 storage
scsi@2:0.0.0 /dev/cdrom disk DVD-RAM writer
Check the PCI Slot on Linux box:
# lspci -v | grep -A 2 "13:00.0" | grep Phy
Physical Slot: 224
Login to ESXi host:
# grep -i scsi[0-9].pciSlotNumber /vmfs/volumes/a*/kb-c02/*.vmx
/vmfs/volumes/a0754ea2-4f1bb7f5/kb-c02/kb-c02.vmx:scsi0.pciSlotNumber = "16"
/vmfs/volumes/a0754ea2-4f1bb7f5/kb-c02/kb-c02.vmx:scsi1.pciSlotNumber = "33"
/vmfs/volumes/a0754ea2-4f1bb7f5/kb-c02/kb-c02.vmx:scsi3.pciSlotNumber = "192"
/vmfs/volumes/a0754ea2-4f1bb7f5/kb-c02/kb-c02.vmx:scsi2.pciSlotNumber = "224"
Based on that information we see that vmdk disks:
# grep -i scsi2:[0-9]*.file* /vmfs/volumes/a*/kb-c02/*.vmx
/vmfs/volumes/a0754ea2-4f1bb7f5/kb-c02/kb-c02.vmx:scsi2:0.fileName = "kb-c02_4.vmdk"
/vmfs/volumes/a0754ea2-4f1bb7f5/kb-c02/kb-c02.vmx:scsi2:1.fileName = "kb-c02_5.vmdk"
are mapped to:
pci@0000:13:00.0 scsi5 storage PVSCSI SCSI Controller
scsi@5:0.0.0 /dev/sde disk 1073MB SCSI Disk
scsi@5:0.1.0 /dev/sdf disk 1073MB SCSI Disk
WARNING: PCI slot number will change when you change the SCSI controller type. It means that your VM will not boot in same corner case scenario see below. PCI slot numbers are increased in area of SCSI controller type. The lowest numbers has LSI Logic Parallel.(I didn't check BusLogic Parallel which is supported only with 32bit OSes)
Let say our VM is configured as follow is bootable and up and running:
VM config file looks like that:
# grep -i scsi[0-9].pciSlotNumber /vmfs/volumes/a*/kb-c02/*.vmx
scsi0.pciSlotNumber = "16"
scsi1.pciSlotNumber = "33"
scsi3.pciSlotNumber = "34"
scsi2.pciSlotNumber = "192"
# grep -i scsi[0-9].virtu /vmfs/volumes/a*/kb-c02/*.vmx
scsi1.virtualDev = "lsilogic"
scsi3.virtualDev = "lsilogic"
scsi2.virtualDev = "pvscsi"
scsi0.virtualDev = "lsilogic"
Someone decided to change the SCSI controller type to 'LSI Logic SAS'
VM config now looks like that and VM cannot boot now the scsi controller order changed this is not Linux uniq on Windows OS we will see the same behaviour.
# grep -i scsi[0-9].pciSlotNumber /vmfs/volumes/a*/kb-c02/*.vmx
scsi0.pciSlotNumber = "224"
scsi1.pciSlotNumber = "33"
scsi3.pciSlotNumber = "34"
scsi2.pciSlotNumber = "192"
# grep -i scsi[0-9].virtu /vmfs/volumes/a*/kb-c02/*.vmx
scsi1.virtualDev = "lsilogic"
scsi3.virtualDev = "lsilogic"
scsi2.virtualDev = "pvscsi"
scsi0.virtualDev = "lsisas1068"
VMware introduced in VM Hardware version 11 new parameters in .vmx file scsiX.sasWWID (I haven't found it in previous VM Hardware versions):
# grep -i scsi[0-9].sas* /vmfs/volumes/a*/kb-c02/*.vmx
scsi2.sasWWID = "50 05 05 62 80 46 0d 80"
scsi3.sasWWID = "50 05 05 62 80 46 0c 80"
scsi0.sasWWID = "50 05 05 62 80 46 0f 80"
This parameter is presented to PVSCSI capabilities. Unfortunately is not presented in LSI controlers:
lspci -v | grep -A 12 "0b:00.0"
0b:00.0 Serial Attached SCSI controller: VMware PVSCSI SCSI Controller (rev 02)
Subsystem: VMware PVSCSI SCSI Controller
Physical Slot: 192
Flags: bus master, fast devsel, latency 0, IRQ 19
I/O ports at 5000 [size=8]
Memory at fd3f8000 (64-bit, non-prefetchable) [size=32K]
[virtual] Expansion ROM at fd300000 [disabled] [size=64K]
Capabilities: [40] Express Endpoint, MSI 00
Capabilities: [7c] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [94] Power Management version 3
Capabilities: [9c] MSI-X: Enable+ Count=24 Masked-
Capabilities: [100] Device Serial Number 80-46-0d-80-50-05-05-62
lspci -v | grep -A 12 "02:01.0"
02:01.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 01)
Subsystem: VMware LSI Logic Parallel SCSI Controller
Physical Slot: 33
Flags: bus master, medium devsel, latency 64, IRQ 19
I/O ports at 2000 [size=256]
Memory at fd5c0000 (64-bit, non-prefetchable) [size=128K]
Memory at fd5e0000 (64-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at fd500000 [disabled] [size=16K]
Capabilities: [f8] PCI Advanced Features
Kernel driver in use: mptspi
Another corner scenario is when we start with LSI Logic SAS controller and attach 3 x PVSCSI controllers the last assigned slot is 1184 the same case will be with 3 x LSI Logic SAS.
# grep -i scsi[0-9].pciS* /vmfs/volumes/a*/kb-c03/*.vmx
scsi0.pciSlotNumber = "160"
scsi1.pciSlotNumber = "224"
scsi2.pciSlotNumber = "256"
scsi3.pciSlotNumber = "1184"
# grep -i scsi[0-9].virt* /vmfs/volumes/a*/kb-c03/*.vmx
scsi0.virtualDev = "lsisas1068"
scsi1.virtualDev = "pvscsi"
scsi2.virtualDev = "pvscsi"
scsi3.virtualDev = "pvscsi"
or
# grep -i scsi[0-9].virt* /vmfs/volumes/a*/kb-c03/*.vmx
scsi0.virtualDev = "lsisas1068"
scsi1.virtualDev = "lsisas1068"
scsi2.virtualDev = "lsisas1068"
scsi3.virtualDev = "lsisas1068"
The pciSlotNumber = "1184" will be translated to Physical Slot: 161
# lspci -v | grep -A 2 "04:00.0"
04:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS1068 PCI-X Fusion-MPT SAS (rev 01)
Subsystem: VMware SAS Controller
Physical Slot: 161
# lspci -v | grep -A 2 "04:00.0"
04:00.0 Serial Attached SCSI controller: VMware PVSCSI SCSI Controller (rev 02)
Subsystem: VMware PVSCSI SCSI Controller
Physical Slot: 161
WARNING: Even the pciSlotNumber is high like 1184 the Linux will see that like Physical Slot 161 it mean your linux drives will be enumerated and the last controller will show as second in Linux !
I am not sure this is a bug or feature I checked that on VMware ESXi 6.0.0 build-3029758.
